tmp

• benpao • 0条评论 浏览次数:1,176 次浏览

==============================================================================
##### How to use this driver #####
==============================================================================
[..]
The UART HAL driver can be used as follows:

(#) Declare a UART_HandleTypeDef handle structure (eg. UART_HandleTypeDef huart).
(#) Initialize the UART low level resources by implementing the HAL_UART_MspInit() API:
    (##) Enable the USARTx interface clock.
    (##) UART pins configuration:
        (+++) Enable the clock for the UART GPIOs.
        (+++) Configure these UART pins (TX as alternate function pull-up, RX as alternate function Input).
    (##) NVIC configuration if you need to use interrupt process (HAL_UART_Transmit_IT()
         and HAL_UART_Receive_IT() APIs):
        (+++) Configure the USARTx interrupt priority.
        (+++) Enable the NVIC USART IRQ handle.
    (##) DMA Configuration if you need to use DMA process (HAL_UART_Transmit_DMA()
         and HAL_UART_Receive_DMA() APIs):
        (+++) Declare a DMA handle structure for the Tx/Rx channel.
        (+++) Enable the DMAx interface clock.
        (+++) Configure the declared DMA handle structure with the required
              Tx/Rx parameters.
        (+++) Configure the DMA Tx/Rx channel.
        (+++) Associate the initialized DMA handle to the UART DMA Tx/Rx handle.
        (+++) Configure the priority and enable the NVIC for the transfer complete
              interrupt on the DMA Tx/Rx channel.
        (+++) Configure the USARTx interrupt priority and enable the NVIC USART IRQ handle
              (used for last byte sending completion detection in DMA non circular mode)

(#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware
    flow control and Mode(Receiver/Transmitter) in the huart Init structure.

(#) For the UART asynchronous mode, initialize the UART registers by calling
    the HAL_UART_Init() API.

(#) For the UART Half duplex mode, initialize the UART registers by calling
    the HAL_HalfDuplex_Init() API.

(#) For the LIN mode, initialize the UART registers by calling the HAL_LIN_Init() API.

(#) For the Multi-Processor mode, initialize the UART registers by calling
    the HAL_MultiProcessor_Init() API.

 [..]
   (@) The specific UART interrupts (Transmission complete interrupt,
        RXNE interrupt and Error Interrupts) will be managed using the macros
        __HAL_UART_ENABLE_IT() and __HAL_UART_DISABLE_IT() inside the transmit
        and receive process.

 [..]
   (@) These APIs (HAL_UART_Init() and HAL_HalfDuplex_Init()) configure also the
        low level Hardware GPIO, CLOCK, CORTEX...etc) by calling the customized
        HAL_UART_MspInit() API.

##### Callback registration #####
==================================

[..]
The compilation define USE_HAL_UART_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.

[..]
Use Function @ref HAL_UART_RegisterCallback() to register a user callback.
Function @ref HAL_UART_RegisterCallback() allows to register following callbacks:
(+) TxHalfCpltCallback        : Tx Half Complete Callback.
(+) TxCpltCallback            : Tx Complete Callback.
(+) RxHalfCpltCallback        : Rx Half Complete Callback.
(+) RxCpltCallback            : Rx Complete Callback.
(+) ErrorCallback             : Error Callback.
(+) AbortCpltCallback         : Abort Complete Callback.
(+) AbortTransmitCpltCallback : Abort Transmit Complete Callback.
(+) AbortReceiveCpltCallback  : Abort Receive Complete Callback.
(+) MspInitCallback           : UART MspInit.
(+) MspDeInitCallback         : UART MspDeInit.
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.

[..]
Use function @ref HAL_UART_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
@ref HAL_UART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) TxHalfCpltCallback        : Tx Half Complete Callback.
(+) TxCpltCallback            : Tx Complete Callback.
(+) RxHalfCpltCallback        : Rx Half Complete Callback.
(+) RxCpltCallback            : Rx Complete Callback.
(+) ErrorCallback             : Error Callback.
(+) AbortCpltCallback         : Abort Complete Callback.
(+) AbortTransmitCpltCallback : Abort Transmit Complete Callback.
(+) AbortReceiveCpltCallback  : Abort Receive Complete Callback.
(+) MspInitCallback           : UART MspInit.
(+) MspDeInitCallback         : UART MspDeInit.

[..]
By default, after the @ref HAL_UART_Init() and when the state is HAL_UART_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
examples @ref HAL_UART_TxCpltCallback(), @ref HAL_UART_RxHalfCpltCallback().
Exception done for MspInit and MspDeInit functions that are respectively
reset to the legacy weak (surcharged) functions in the @ref HAL_UART_Init()
and @ref HAL_UART_DeInit() only when these callbacks are null (not registered beforehand).
If not, MspInit or MspDeInit are not null, the @ref HAL_UART_Init() and @ref HAL_UART_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).

[..]
Callbacks can be registered/unregistered in HAL_UART_STATE_READY state only.
Exception done MspInit/MspDeInit that can be registered/unregistered
in HAL_UART_STATE_READY or HAL_UART_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
using @ref HAL_UART_RegisterCallback() before calling @ref HAL_UART_DeInit()
or @ref HAL_UART_Init() function.

[..]
When The compilation define USE_HAL_UART_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available
and weak (surcharged) callbacks are used.

 [..]
    Three operation modes are available within this driver :

 *** Polling mode IO operation ***
 =================================
 [..]
   (+) Send an amount of data in blocking mode using HAL_UART_Transmit()
   (+) Receive an amount of data in blocking mode using HAL_UART_Receive()

 *** Interrupt mode IO operation ***
 ===================================
 [..]
   (+) Send an amount of data in non blocking mode using HAL_UART_Transmit_IT()
   (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_TxCpltCallback
   (+) Receive an amount of data in non blocking mode using HAL_UART_Receive_IT()
   (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_RxCpltCallback
   (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can
        add his own code by customization of function pointer HAL_UART_ErrorCallback

 *** DMA mode IO operation ***
 ==============================
 [..]
   (+) Send an amount of data in non blocking mode (DMA) using HAL_UART_Transmit_DMA()
   (+) At transmission end of half transfer HAL_UART_TxHalfCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_TxHalfCpltCallback
   (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_TxCpltCallback
   (+) Receive an amount of data in non blocking mode (DMA) using HAL_UART_Receive_DMA()
   (+) At reception end of half transfer HAL_UART_RxHalfCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_RxHalfCpltCallback
   (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can
        add his own code by customization of function pointer HAL_UART_RxCpltCallback
   (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can
        add his own code by customization of function pointer HAL_UART_ErrorCallback
   (+) Pause the DMA Transfer using HAL_UART_DMAPause()
   (+) Resume the DMA Transfer using HAL_UART_DMAResume()
   (+) Stop the DMA Transfer using HAL_UART_DMAStop()

 *** UART HAL driver macros list ***
 =============================================
 [..]
   Below the list of most used macros in UART HAL driver.

  (+) __HAL_UART_ENABLE: Enable the UART peripheral
  (+) __HAL_UART_DISABLE: Disable the UART peripheral
  (+) __HAL_UART_GET_FLAG : Check whether the specified UART flag is set or not
  (+) __HAL_UART_CLEAR_FLAG : Clear the specified UART pending flag
  (+) __HAL_UART_ENABLE_IT: Enable the specified UART interrupt
  (+) __HAL_UART_DISABLE_IT: Disable the specified UART interrupt
  (+) __HAL_UART_GET_IT_SOURCE: Check whether the specified UART interrupt has occurred or not

 [..]
   (@) You can refer to the UART HAL driver header file for more useful macros

@endverbatim
[..]
(@) Additionnal remark: If the parity is enabled, then the MSB bit of the data written
in the data register is transmitted but is changed by the parity bit.
Depending on the frame length defined by the M bit (8-bits or 9-bits),
the possible UART frame formats are as listed in the following table:
+————————————————————-+
| M bit | PCE bit | UART frame |
|———————|—————————————|
| 0 | 0 | | SB | 8 bit data | STB | |
|———|———–|—————————————|
| 0 | 1 | | SB | 7 bit data | PB | STB | |
|———|———–|—————————————|
| 1 | 0 | | SB | 9 bit data | STB | |
|———|———–|—————————————|
| 1 | 1 | | SB | 8 bit data | PB | STB | |
+————————————————————-+

  • @attention
    *
  • © Copyright (c) 2016 STMicroelectronics.
  • All rights reserved.
    *
  • This software component is licensed by ST under BSD 3-Clause license,
  • the “License”; You may not use this file except in compliance with the
  • License. You may obtain a copy of the License at:
  • opensource.org/licenses/BSD-3-Clause
    *

*/

/* Includes ——————————————————————*/

include “stm32f1xx_hal.h”

/** @addtogroup STM32F1xx_HAL_Driver

  • @{
    */

/** @defgroup UART UART

  • @brief HAL UART module driver
  • @{
    */

ifdef HAL_UART_MODULE_ENABLED

/* Private typedef ———————————————————–/ / Private define ————————————————————/ /* @addtogroup UART_Private_Constants

  • @{
    / /*
  • @}
    / / Private macro ————————————————————-/ / Private variables ———————————————————/ / Private function prototypes ———————————————–/ /* @addtogroup UART_Private_Functions UART Private Functions
  • @{
    */

if (USE_HAL_UART_REGISTER_CALLBACKS == 1)

void UART_InitCallbacksToDefault(UART_HandleTypeDef *huart);

endif /* USE_HAL_UART_REGISTER_CALLBACKS */

static void UART_EndTxTransfer(UART_HandleTypeDef *huart);
static void UART_EndRxTransfer(UART_HandleTypeDef *huart);
static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma);
static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma);
static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma);
static void UART_DMAError(DMA_HandleTypeDef *hdma);
static void UART_DMAAbortOnError(DMA_HandleTypeDef *hdma);
static void UART_DMATxAbortCallback(DMA_HandleTypeDef *hdma);
static void UART_DMARxAbortCallback(DMA_HandleTypeDef *hdma);
static void UART_DMATxOnlyAbortCallback(DMA_HandleTypeDef *hdma);
static void UART_DMARxOnlyAbortCallback(DMA_HandleTypeDef *hdma);
static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart);
static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart);
static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart);
static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout);
static void UART_SetConfig(UART_HandleTypeDef *huart);

/**

  • @}
    */

/* Exported functions ———————————————————/ /* @defgroup UART_Exported_Functions UART Exported Functions

  • @{
    */

/** @defgroup UART_Exported_Functions_Group1 Initialization and de-initialization functions

  • @brief Initialization and Configuration functions
    *
    @verbatim
    ===============================================================================
    ##### Initialization and Configuration functions #####
    ===============================================================================
    [..]
    This subsection provides a set of functions allowing to initialize the USARTx or the UARTy
    in asynchronous mode.
    (+) For the asynchronous mode only these parameters can be configured:
    (++) Baud Rate
    (++) Word Length
    (++) Stop Bit
    (++) Parity: If the parity is enabled, then the MSB bit of the data written
    in the data register is transmitted but is changed by the parity bit.
    Depending on the frame length defined by the M bit (8-bits or 9-bits),
    please refer to Reference manual for possible UART frame formats.
    (++) Hardware flow control
    (++) Receiver/transmitter modes
    (++) Over Sampling Method
    [..]
    The HAL_UART_Init(), HAL_HalfDuplex_Init(), HAL_LIN_Init() and HAL_MultiProcessor_Init() APIs
    follow respectively the UART asynchronous, UART Half duplex, LIN and Multi-Processor configuration
    procedures (details for the procedures are available in reference manuals
    (RM0008 for STM32F10Xxx MCUs and RM0041 for STM32F100xx MCUs)).
声明: 本文采用 BY-NC-SA 协议进行授权，如无注明均为原创，转载请注明转自 走着的小站
本文地址: tmp